GM300 Mobile Radios Operating Instructions Operating Instructions 8 Channel Operating Instructions To Turn The Radio On Turn the ON/OFF VOLUME knob to the right until it clicks. The LED lights will show the last status of the radio and a start-up tone will be heard. To Receive Set the volume by turning the ON/OFF VOLUME knob clockwise. After searching for the genuine Motorola program I came across Motorola Radius GM300 Radio Doctor. This program runs fine under Windows XP and will do all the functions that the genuine Motorola radio service software does. Here is the main screen.
- Gm300 Programming Software
- Motorola Radius Gm300 Radio Doctor Software
- Motorola Radius Gm300 Radio Doctor
- Motorola Radius Gm300 Programming Software
- Programming Software For Motorola Gm300
Software radius gm300 radio doctor
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
Software radius gm300 radio doctor I just got my laptop upgraded from windows 8. Click on the image to enlarge it. Radio Doctor for MOTOROLA RADIUS GM300 versi 1. Radio Modification and Descriptive Articles: Caution: A lot of the information in the articles. The RSS is shipped on. The XV- series seems to all be 1 channel radios. Motorola radius gm300 radio doctor for windows 2000xp dos. Try to reprogram your. For example to program 4. When you enter the. С уважениемАндрей 20 декабря 2011 г. Motorola Radius programming instructions using Windows. If so, you are now good to go. MDF file, just in case you make a mistake. В переходнике для радиостанций MOTOROLA GP-340 предусмотрено. Radio Doctor for GM300 ver. Oleg EX8MLT has proposed HYT TC-500 radios connector. This makes it easier to remote- mount a GM3. The GM300 Radio Doctor piece of software did a good job at being able to program this ancient. Потом пошли транки была Моторола GM300 в машине, GP300. I know this is a common topic, but I have not been able to get anything to work in my weeks of searching, and I could really use some help. You will find that in some cases the. Возникла проблемка с чем к Вам и пожаловал. Software radius gm300 radio doctor Free download gm300 radio doctor Files at Software Informer. NOT ground either pin 1 or pin 1. They turn into a binary coded input that allows you to. I personally would not. See below for update to programming interface. People have apparently modified the RSS to get 1. RIB- IVG Radio Programming.
Introduction.
The Motorola GM300 can be re-programmed quite easily to allow use on our Amateur Radio bands. The radio is made in both a VHF and UHF versions, and makes an excellent 2mtr or 70cms mobile/base station radio.
Most of the radio's I have worked on have originally been 8 channel units. These can be modified to operate on 16 channels quite easily.
The programming interface can be made for a low cost. All it consists of is a RS232 to TTL level converter, that connects between the serial port of your PC and the radio's microphone socket.
Amateur Radio Conversion.
Gm300 Programming Software
The radio requires the Motorola Software which can be found if you ask around or search for it on the FTP sites on the Internet. If you can't find it then try your local Motorola dealer who should be able to help at a small cost.
You also have to make an interface, or purchase one.
Motorola Radius Gm300 Radio Doctor Software
To program the radio onto the Amateur band, you can find some versions of software that have been hacked into allowing frequencies to be entered to bring the radio into the amateur bands which normally are just bellow the original working frequency. However this depends on your version of software, if it's a un-hacked version then you have to press the
Motorola Radius Gm300 Radio Doctor
16 Channel conversion. (for 8 channel radio's only)
Motorola Radius Gm300 Programming Software
To program the radio for 16 channels all you need to do is edit a file called GM300.MDF. You do this with the help of a Hex editor such as Hex Workshop. The file you need to modify is called GM300.MDF and can be found in the main directory of the Motorola software. Keep a backup of your original GM300.MDF file, just in case you make a mistake.
I have made a small video that shows the Hex Workshop screen during the modification. This should help you understand the procedure of editing the file which when complete will give you 16 channels. Click below to download.
Procedure
Programming Software For Motorola Gm300
- Get a copy of Hex Workshop
- Start the Hex Workshop program and open the file GP300.MDF to begin editing.
- Go to 'Tools', and the 'Generate Checksum'.
- Make sure 'Entire Document' and also 'Decimal' are ticked. Then press 'Generate'.
- Look in the 'Checksum-16' box, in my version of software for example this results in a checksum of 5514. (yours may be a different number depending on the version of Motorola software)
- Write this number down, as you need it later.
- Press 'Cancel' to return to the main window and your next step.
- Go to 'Edit' and then 'Find'. A pop-up window appears.
- You need to enter the model number of your radio. For e.g. M34GMC00D3AA.
- When you enter the model number leave off the last two letters(AB on my radio).Make sure 'ASCII' is ticked.
- When you press 'Find Next', you will see your model number highlighted.
- If you count 8 numbers after the highlighted section, you should see the number '08' as long your radio is originally a 8 channel set.
- Edit the '08' to '10' (note 10 in Hex is equal to 16 in decimal).
- You now need to edit the start of the program, to allow the software to run.
- In the first few lines look for a Hex number that you can easily take away 8 from.
- In my software at address 00000040 you will see the number '78' on the right.
- Edit this to be '70'.
- Now you must do a final checksum and make sure it equals the original value.
- If this is the same, then replace you original file with the modified file.
- Try to reprogram your radio with the extra 8 channels to give you 16 channels.